Gtco 2500 Series - Users Guide 2/3 Manuel d'utilisateur

2500 Series 1 Table of Contents Data Output Formats Format Definitions Model-to-Format Conversion ASCII Output Formats Bin

2500 Series 10 (MSB) FORMAT 28 (LSB) BYTE B7 B6 B5 B4 B3 B2 B1 B0 1 2 3 4 5 0 0 0 0 0 1 0 0 0 0 C3 X5 X11 Y5 Y11 C2 X4 X10 Y4 Y10 C1 X3 X9 Y3

2500 Series 11 BINARY FORMATS 16-Button Cursor Output BUTTON PRESSED FORMAT 24, 26 AND 28 FORMAT 27 AND 31 FORMAT 29 AND 30 FORMAT 23 AND 25

2500 Series 12 Operating Modes The operating mode sets the conditions that must be satisfied before the tablet will transmit position to the h

2500 Series 13 RUN TRACK INCREMENT Tablet outputs data points continuously. This mode is called STREAM by some manufacturers. Tablet

2500 Series 14 o Tablet to RS-232 connection? o Host to RS-232 connection?  Is the RS-232 cable plugged into the correct communications po

2500 Series 15 up. The Comprehensive tests are more detailed diagnostic tests meant for the use of trained factory or field service engineers

2500 Series 16 Soft Switch Assignments in Test State The tablet uses the following switch assignments for running the tests from the soft sw

2500 Series 17 Switch 7: Spare Switch 8 Spare BANK 2: Model ID BANK 3: Software ID BANK 4: Analog to Digital Converter BANK 5:

2500 Series 18 COMPREHENSIVE TESTS MODEL ID SOFTWARE ID ANALOG TO DIGITAL TEST INPUT TEST GRID TEST CHECKSUM OUTPUT

2500 Series 19 b5 b6 b7 button is pressed (cursor line status) Cursor Present 4-Button Cursor Present Reserved Test Commands The diagnostic

2500 Series 2 Data Output Formats The output format is the manner in which ASCII or binary characters are transmitted from the tablet to repre

2500 Series 20 ESC % _ _ 4 CR ANALOG TO DIGITAL TEST ESC % _ _ 5 CR INPUT TEST ESC % _ _ 6 CR GRID TEST ESC% _ _ 7 CR CHECKSUM OUTPUT E

2500 Series 21 Changing the Operating Voltage The tablet may be operated at 100-125 Volts AC or at 200-250 Volts AC. If the operating voltage

2500 Series 22 5. Reinstall the selector card. The printed side of the card must face the power cord connector and the indicator pin must po

2500 Series 23 3. Reinstall the cover assembly. The indicator pin should now be visible in the 240V position. NOTE: For protection against

2500 Series 24 5 6 7 8 9-19 20 21-23 24 25 Clear to Send Input, +12V pull-up Data Set Ready Input, +12V pull-up Signal Ground

2500 Series 25 25035-01 25036-01 4-Button Cursor, Diamond Shape 16-Button Cursor STYLUS 25093-01 25094-01 25097-01 Stylus w/o Ink Stylus w/Blu

2500 Series 26 Operating Temperature Storage Temperature Humidity Range Operating Altitude Storage Altitude 60° to 105° F; 15° to 40° C -131°

2500 Series 27 Corporate Headquarters 14557 N. 82nd Street Scottsdale, Arizona 85260 Tel: 1-866-746-3015 Support: 1-866-746-3015 Fax: 480-9

2500 Series 3 Line Feed (<LF>) LPmm, LPI M MSB, LSB N P Space (<SP>)> in output data format Sx and Sy T T0

2500 Series 4 Xn or Yn symbols represents the allowable number of digits in any output. Data Bit. In binary formats, a bit representing c

2500 Series 5 Kurta Series 2 ASCII 10 Kurta Series 2 Binary 24 Numonics 2200 23 Summagraphics Bit Pad 1 ASCII 0 Summagraphics Bit Pad 1 Binar

2500 Series 6 >509 LPI, >20 LPM C XXXXX SP YYYYY CR 10 <510 LPI, <21 LPM >509 LPI, >20 LPM C XXXX YYYY CR C XXXXX YYYYY CR 1

2500 Series 7 BUTTON PRESSED 8, 15, 16 IN PROX 8, 15, 16 OUT OF PROX 1 RUN MODE 1 OTHER MODES PEN UP PEN DOWN NONE 0 1 2 3 4 5 6 7 8 9 A B C

2500 Series 8 4-Button Cursor Output ASCII FORMATS BUTTON PRESSED 0, 2, 9, 10 AND 11 12 AND 14 PEN UP PEN DOWN NONE 0 1 2 3 0 1 2 4 8 SP 1 2

2500 Series 9 (MSB) FORMAT 24 (LSB) BYTE B7 B6 B5 B4 B3 B2 B1 B0 1 2 3 4 5 6 1 0 0 0 0 0 M X13 X6 0 Y13 Y6 C3 X12 X5 0 Y12 Y5 C2 X11 X4 0 Y11