Gtco Summagrid IV - Users Guide Part 3 Manuel d'utilisateur

Summagrid IV 1 Part 3 provides technical information about Summagrid IV. You’ll find the following appendices in Part 3: Appendix A Appendix B

Summagrid IV 10 Appendix C ASCII Conversion Chart

Summagrid IV 11

Summagrid IV 12

Summagrid IV 13 Appendix D GTCO Format Emulation The Summagrid IV can emulate the GTCO output format. This chapter provides the binary and ASCII

Summagrid IV 14 Refer to the key for definitions of the format characters. For reports, low resolution is: FXXXXSYYYY<CR><LF> For r

Summagrid IV 15 NOTE: The cursors are designed for single, not multiple button use. Pressing multiple buttons simultaneously yields unpredictab

Summagrid IV 16 Flag Bit Definitions for 16-Button Cursor Flag Bit Definitions for Two-Button Stylus and Four-Button Cursor

Summagrid IV 17 D.1.3 RS-232 Hardware Interface The Summagrid IV can emulate two kinds of GTCO binary formats: low and high resolution. Low Re

Summagrid IV 18 D.1.4 GTCO DIP Switch Settings When configuring Summagrid IV in the GTCO format, the DIP switches perform the same functions exc

Summagrid IV 19 Appendix E CalComp Format Emulation The Summagrid IV can emulate the CalComp 9100 output format. This chapter provides the binar

Summagrid IV 2 A.1 Summagrid IV Interfacing Hardware A.1.1 RS-232 Hardware Interface The Summagrid III’s interfacing hardware complies with t

Summagrid IV 20 Refer to the key for definitions of the format characters. Format 1 (1000 LPI, 40 LPMM) <T><M><C>XXXXXYYYYY&l

Summagrid IV 21 Character Definition T M P X , Y C Tablet status character Mode status character R = Run U = Line P = Point T = Track

Summagrid IV 22 NOTE: Cursors are designed for single, not multiple, button use. Pressing multiple buttons simultaneously yields unpredictable

Summagrid IV 23 E.1.3 Packed Binary Report Format The Summagrid IV can emulate two types of CalComp binary formats: low and high resolution. Lo

Summagrid IV 24 Character Definition LSB MSB P C0-C4 Least significant bit Most significant bit Parity bit Flag bit, identifying the transducer

Summagrid IV 25 Flag Bit Definitions for the Two-Button Stylus and Four-Button Cursor E.1.4 CalComp DIP Switch Settings When configuring Summa

Summagrid IV 26 Appendix F MM/SummaSketch Format Emulation The Summagrid IV can emulate the Summagraphics MM/SummaSketch output format. This cha

Summagrid IV 27 F.1.2 Binary Report Format Binary Format for Absolute Coordinates Binary Format for Relative Coordinates F.1.3 ASCII BCD

Summagrid IV 28 Character Definition X , Y F X coordinate digit, where each digit is an ASCII character from 0 to 9. ASCII comma Y coordina

Summagrid IV 29 Flag Bit Definitions for the Stylus and Four-Button Cursor Sx and Sy T PR PH X0, X1… Y0, Y1…. X and Y coordinate signs. 1

Summagrid IV 3 9-pin-to-25-pin AT Adapter Cable

Summagrid IV 30 F.1.4 MM/SummaSketch Command Summary

Summagrid IV 31 F.1.5 MM/SummaSketch DIP Switch Settings When configuring Summagrid IV in the MM/SummaSketch format, the DIP switches perform t

Summagrid IV 32 Appendix G Summagrid IV Specifications Physical Specifications Tablet Size Active Area Un-Boxed Weight (Tablet & Controll

Summagrid IV 33 Environmental Specifications Operating Environment Non-Operating +45 degrees to +100 degrees Fahrenheit +7 degrees to +43 deg

Summagrid IV 34 Appendix H Summagrid IV Application Set Up This appendix provides DIP switch settings for the popular software applications. Th

Summagrid IV 35

Summagrid IV 36

Summagrid IV 37

Summagrid IV 4 Appendix B Summagrid IV DIP Switch Settings B.1 B.1 B.2 Summagrid IV DIP Switch Settings Summagrid IV DIP Switch Table Summagrid I

Summagrid IV 5 B.1.2 Summagrid IV DIP Switch B

Summagrid IV 6 B.1.3 Summagrid IV DIP Switch C

Summagrid IV 7 B.2 Summagrid IV vs. Microgrid II Switch Settings B.2.1 Summagrid IV DIP Switch A

Summagrid IV 8 B.2.2 Summagrid IV DIP Switch B

Summagrid IV 9 B.2.3 Summagrid IV DIP Switch C